Bematech KC-4112 Rev.1.0 Manual do Utilizador

10Paper handlingLoading PaperTo insert a new paper roll, please do as follows:The end of the paper roll mustbe cut evenly, as shown on theright.Be sur

11Key PanelThe key panel gives visual printer status and manual control to the operator.These functions are accomplished using one switch and LEDs, de

12Operation ModesThe printer can be operated in the following modes:Normal (Remote mode)In this state, the printer is being controlled by the host thr

13Figure 1425...24...23...22...21...20...19...18...17...16..

14...17...16...13...12...11...10...09...

15Signal pin1011121314,15,18,36161719-303132333435Associatedreturn pin282930Signal/ACKBUSYPEOL OUTNCGNDFrameGND/INIT/ERRORGNDNCPULLUPDescriptionThis p

16Characteristics SpecificationsPrintingMethod: Thermal Line PrintingDot Density: 8 dots/mm (203 dpi x 203 dpi)Print Width: 104 mm (4.1”) (832 dot-pos

17Dip Switch Function1 Reserved Must be in off position2 PNE ** On: activatedOff: not activated3 Baud Rate On: 115200 bpsOff: 9600 bps *4 Stop Bits On

18Chapter 7General FlowchartGeneral FlowchartGeneral FlowchartGeneral FlowchartGeneral FlowchartRESETINIT PRINTERErrorMechanism?Error Cuter?Verify Pan

19General Flowchart DescriptionInitializationAfter a hardware reset, the following steps are performed:- The system verifies if there is a mechanism e

2KC-4112 Service´s ManualP/N: 6705 . Rev.1.0December 2005(First edition)Copyright by Bematech S.A. Curitiba, Brazil.All rights reserved.No part of th

20Chapter 8Block DiagramBlock DiagramBlock DiagramBlock DiagramBlock DiagramControl BoardRS232CentronicsSensorsThermalMechanismDriverKeyboard&LEDs

21This section describes tests that are implemented in the kiosk printer microcode (firmware) as well as SWs thatmay be run in order to help diagnosin

22The PAPER LED is on blinking under the following conditions:Condition Number Of BlinksHead-Up Unlocked ContinuouslyWithout Paper Is OnWith Paper and

23Chapter 10TTTTTrrrrroubleshootingoubleshootingoubleshootingoubleshootingoubleshootingThis Chapter shows possible solutions to some of the more usual

24Possible CauseThe serial cable has one or more lines with faultyconnections / broken wiresThe pin layout does not meet the specificationThe baud rat

25ERRO LED coded problemsDiagnosing general failures by cheking the Error LED on the printer key panelRESETSelf teststarted ?Turn printer onwith Paper

26ErrorMechanismPower SupplyCutterPrinte HeadTemperatureEntrance Presenter jamExit Presenter jamNumberof Blinks81112151616TypeNon-recoverableNon-recov

27Chapter 11RRRRReplacing Defective Peplacing Defective Peplacing Defective Peplacing Defective Peplacing Defective Parts or Modulesarts or Modulesart

281.4 Take off the cables from the opening in the control board box.1.5 Cut to liberate the cables and remove the side screws.

291.6 Cut the fastener and remove the side screws.FRU90022 - FRU KC4112 PRESENTER FULL

3EMC and Safety Standards AppliedProduct Name: KC-4112Model Name: 6200 and 6300 (all)*EMC is tested using an EPSON PS180 power supplyEurope: CE markin

30FRU90023 - FRU KC4112 PRES KIT2.1 Remove the screws. (2x).2.2 Pull in the sense of the arrows to remove. 2.3 Remove the screws. (2x).2. FRU90023 - F

313. FRU90024 - FRU KC4112 TH MECH KIT3.1 Cut to liberate the cables.3.2 Remove the screws. (7x).3.3 Remove the e-ring (1x).FRU90024 - FRU KC4112 TH M

324. FRU90025 - FRU KC4112 CUTTER KIT4.1 The process to loosen the cutter is the same of the presenter. (1.0 up to 1.6)FRU90025 - FRU KC4112 CUTTER KI

335. FRU90026 - FRU KC4112 CTR BOARD DUAL5.1 disconnect the cables5.2 Remove the screws. (x4).FRU90026 - FRU KC4112 CTR BOARD DUAL

346. FRU90027 - FRU KC4112 CABLE KIT6.3 Remove the screws to liberate the panelof the keyboard and key on/off.6.1 Remove the screws to liberate the pa

356.2 To set up the screws in the following order6.2 To set up the screws in the following orderFRU90027 - FRU KC4112 CABLE KIT

36Chapter 12Preventive MaintenancePreventive MaintenancePreventive MaintenancePreventive MaintenancePreventive MaintenanceCleaning the Presenter:Remov

37See details on the lubrication points in figures below.Parts to be cleaned and lubricated:

38KC-4112 is available with two options:- With presenter and cut . (6200 - PB20 DRL1PR33 STACKED)- Without presenter, with cut . (6300 - PB20 DRL1FC33

39Configuration *DualPrinter with presenter(stacked version)Printer withoutpresenter (StackedVersion)Printer with presenter(Low Profile)Printer withou

4Safety PrecautionsThis section presents important information intended to ensure safe and effective use of this product. Pleaseread this section care

40Appendix BField Replacement UnitField Replacement UnitField Replacement UnitField Replacement UnitField Replacement Unit1. FRU90022 - FRU KC4112 PRE

414. FRU90025 - FRU KC4112 CUTTER KIT5. FRU90026 - FRU KC4112 CTR BOARD DUAL6. FRU90027 - FRU KC4112 CABLE KIT

42The kiosk printer has the capability to receive firmware updates from PC using ther RS-232 (COM1 or COM2) port.This section explains the SW used to

43- The default interface is COM1 and baud-rate 115.200 bps.- To choose other interface, select the interfaces TAB and changes interface.- Select the

44- The ERROR and PAPER LEDs on the kiosk printer start blinking.- Use the Output Window to follow the update progress.- The flash update will take a

Appendix DAssembliesControl Board Box45

Printer Mechanism Module46

Presenter47

Stacked without Presenter48

Stacked with Presenter49

5SummarSummarSummarSummarSummaryyyyyChapter 1 - Introduction ... 6Chapter

Low Profile with Presenter50

Low Profile without Presenter51

Side Mount with PresenterSide Mount without Presenter52

Cut and drop53

6Chapter 1IntroductionIntroductionIntroductionIntroductionIntroductionHow this manual is organized:• Chapter 2 and 3 refers to product presentation (u

7Chapter 2Getting StartedGetting StartedGetting StartedGetting StartedGetting StartedThe printerThe communication connectors, DC connector, On/Off swi

8Paper holderDamping deviceSpindlePaper near end sensorFigure 3Paper roll is not included – the appropriate thermal paper should be used. Refer to th

9GROUNDFigure 4PoweringMake sure that the printer is turned off.Connect the power cord to the power supply‘sAC connector and to an electrical outlet.